Author: samil

Planning To Setup A Hot Water System Soon? Everything You Need To Know About..

In cold weather conditions, when temperature goes down. Hot water systems come to the rescue. Hot water is used for varied range of domestic use. For the continues flow of hot water that too at the perfect temperature one needs to understand how the hot water flow system works. The heat transfer mechanism varies greatly depending on, the type of hot water system that is installed. In this article from plumber Mississauga  we will be discussing about some of the common types of geyser.

Pressure type geysers

The pressure is generated by the overhead tank.  This pressure is used to channel the water to the various outlets. There is continuous inflow of cold water and outflow of hot water. That way at no point the electric heating element is vacant. Thus this eliminates the possibility of burning out of the component. The installation part is very crucial as, it decides how well the geyser will handle the pressure.

Non-Pressure type geysers

This geyser remains full of water, a thermostat is installed. It has a single outlet which dispatches hot water, when the valve of the cold water is open.

Instantaneous type of geyser

In this system, an heating element is wound around a pipe. The drawback of this system is, if the water is hard water, there is formation of scales. These depositions of scale choke the pipe, thus decreasing the pressure flow.

Safety devices to be installed in the geysers

There is lots of multiple pressure variations and heat transfer in a geyser, which means it works under multiple temperature range. So as an safety measure offered by plumber Toronto, one has to select the best of the construction material which can handle the fluctuating temperature and pressure change. Also, the geyser has to be installed with temperature and pressure relief valves. A vacuum breaker is to be installed so as to provide it with negative pressure.

The geysers come in various capacities, so before investing in buying a geyser. One has to calculate the estimate daily requirement of hot water. And then accordingly with a considerable upper and lower limit, the geyser with the required capacity has to be brought. Also it has to be kept in mind, the hot water requirement varies greatly with occasions, and thus the upper limit has to be set accordingly. Instead of installing multiple geysers at various points in the house, it is also advisable to adopt the new system of Centralized –hot water system. In this system, peak hot water demand is fulfilled. It is also economical, it avoids overloading of power and maintenance and fuel cost is also pocket friendly.

When it comes to house hold appliances, Geyser tops the list of one of the most expensive and highly required machines. So, one has to take every care that while selecting one, the investment is made wisely. No compromise with the quality, safety and the capacity of the geyser is to be made. Also, one has to take care of the fact that. Over spending unnecessarily is to be avoided.

Reasons Why Investing In Quality Plumbing Materials Is More Important Than You Think

Sparing a dime today can cost you a dollar later. If you are thinking of building a sturdy and stress-free home, it is imperative for you to invest in good quality plumbing supplies. There are a number of funnels, pipes, flushes, faucets, and connections available in the market that hold the framework together when installed, but they give up at the slightest wear and tear and can cause a flood in your dazzling home. Here are a few significant things which you should definitely consider:

Bathrooms Are Important

A restroom is a vital space in a house. We invest more energy than we might suspect in the lavatory. A good bath can make you relaxed and help you unwind yourself. It is a place to relieve yourself, to get dressed, to brush teeth, and to give you the much needed burst of morning freshness. A look at a leaking pipe or a cracked faucet, at the early hours of your morning, can ruin your mood for the entire day. Thus, it is essential that the plumbing material you use is durable and beautiful at the same time. You don’t revamp a washroom consistently, then why not put resources in some great quality pipes and spare yourself some extra efforts in the long haul?

Safety

It is essential to comprehend the dangers involved with low-quality plumbing systems. For example, a poor grade funnel used in your gas water heater installation can put a massive risk to your safety or a poor quality metal pipe can contaminate your drinking water with rust. A small leak is all that it takes to cause a great deal of damage in time and sudden big leaks or a faulty faucet can bring havoc to your day. It is crucial to install good quality plumbing supplies to ensure the well-being of your home with the help of plumber Toronto.

Inconvenience

If you have ever had water clogging issues in your home, you know what we’re talking about. It is a long and difficult task to clear up the mess. Plumbing problems are annoying to a great degree, even though a call to plumber Toronto will save your day. Such a situation is less likely to arise if you invest in good quality plumbing materials.

Durability

The renovation or a refurbishing of a bathroom takes a long while in an average household due to monetary issues or maybe because you feel happy the way things are. It is not only daunting, but expensive and time-taking as well. Therefore, it is important to employ expert quality plumbing materials that are durable to the last mile and does not become a reason for your inconvenience halfway.  They might cost you some additional cash, but quality plumbing supplies will be great now and will be as incredible in the next 10-15 years until you think about upgrading them.

Pipes and funnels, flushes and faucets, connections and associations, are the unsung heroes of your home. When people think about refashioning their homes, they mostly think about investing in the visible areas, but a good plumber Toronto is integral to hold up your roof together and adds a great deal to the aesthetics of your home as well.  Remember all of these reasons to invest in good quality plumbing materials on your next purchase and spare yourself a frantic call to the plumber.

3 Extremely Useful DIY Plumbing Tips Everyone Should Know

Why pay the plumber, when you can do it all by yourself. It becomes a real menace to wait for the plumber, every time a problem arises in your plumbing system. In a century where expenses are so high, save your few bucks with a little knowledge and know-how about your plumbing system, its equipment and the related problems with easy solutions. The plumbing tips here are sponsored by Mississauga plumber:

1. Clearing clogged pores and uneven sprays of the shower head and faucets

Water quality varies in every zone. Though we received treated water in our houses, still depending on the hardness of water. Scales start to form in the various chambers of our plumbing equipment. The first sign of sedimentation appears when water spray from the shower heads and faucets, comes out uneven. If this problem isn’t addressed, gradually most of the pores get clogged up. It leads to build up of pressure inside the pipes, which might lead to bursting of the pipe. This problem can be solved with the magic of vinegar. Vinegar is readily available in every house hold, the ideal way is to use a shower cap or plastic, fill it with vinegar dip the clogged poured in the solution and leave it overnight. Vinegar reacts with the scale and breaks the lime. By day light the pores are cleaned, deposits are gone. They can be restored back to use.

2. Faulty Geyser? Here is the easiest repair

Geysers aren’t that complicated machines, yet many problems crop up when using one. Few of them need professional help from a plumber, while few can be solved in minutes. Firstly, fluctuating temperature, flow of very hot water. Even after the installation of new geyser, the temperature seems to be very high. No need to panic, every geyser has a pre installed setting for temperature, one needs to manually adjust the temperature range.  Once it is set to your desired degree, the water will flow fine. If your geyser stops heating water, one should check the circuit breaker. It is a safety feature. In case of overload, the circuit breaker saves the geyser from burn out and short circuit. Simply replacing the circuit breaker should solve your problem.

3. Clean clogged pipes and drains

This is a universal problem. In autumn, the dried leaves and debris play their role in clogging the drain. In winter, the water freezes thus breaking down whole the system. Plumber Toronto can help you with this problem. So let’s see how to get it cleaned. If the clogging is due to scale deposition, running of hot water and some cleaning solution in a high pressure helps clear the deposits. In case of debris, a vacuum zone is created, which bars the movement of the garbage. So a reverse suction should be used. Once cleaned, strainers should be installed. Now as winter approaches, the water starts to freeze. So the most logical of the solution is using jacketed or insulated pipes. Also valves can be used to cut out the unnecessary pipe ways.

So fold your sleeves up, and get it all done following the above tips.

 

Tankless Water Heaters- DIY Plumbing Tips to Get it at Home

So, when your much anticipated holidays are just around the corner, you must be looking for a refreshing week with your friends and family. And also some time to revitalize your drooping spirit. But, when you finally get into the shower, what you find is nothing but ice-cold water, because the hot water systems at your place are damaged. Well, the ideal solution, according to Plumber Toronto, to deal with this situation is simply investing in tank-less water heater, also known as instantaneous heaters.

What are Tankless Water Heaters?

Tankless water heaters are no different from a standard water storage tank heater and operate in the same way as the latter. The tankless system can usually heat up 50 gallons of water and keeps on continually heating the water to maintain a constant temperature. Once some quantity of hot water is used, the system gets refilled by itself. The tank uses high energy to maintain a constant temperature. No doubt, the automated system makes tankless heater highly effective.

Benefits of using Tankless Water Heaters

The good news is Tankless water heaters are easy to maintain and they are highly efficient. Not only does it save you maintenance cost, but also help you get the plumbing done at low cost. Infact, you can get the system upgraded at low cost.

DIY Plumbing Tips for Upgrading Tankless Water Heaters

You can easily cut down the plumbing cost by using these tips. Read on to know how to upgrade the system without hiring a plumber.

Prepare the Tank

Shut off the water flow in the cold side of the water heater. Now unfasten hot water faucet to alleviate some pressure in the lines.Now, turn off the power at the breaker. Once it’s done, drain out about a gallon of water to relieve complete pressure and it will help to lower the water level.

Relieve pressure from the pipes

With the help of a measuring tape, estimate the length of each section of 3/4″ copper (or any other metal if used) pipe.Cut it into pieces of equal length. Now assemble the pieces together with any fittings. Now screw the adaptors in proper place, so that the pieces can be fit together. Now place the assembled pipe and check if the measurement is fine.

Cut the water line cautiously

Once the pipe is done, the pre-fitted valve assembly should be aligned in the cold water. Dip it until it makes a proper 90-degree angle intersecting the water line. With a pipe cutter you can easily cut the pipe closest to the water line firs. Move it to the top of the pipe and cut down the excess part.

Assemble the Expansion Tank Connections

While cutting down the pipe, make sure that the length of the pipe coming off as the ‘T’ is extremely short to alleviate the strain on the connection.Clean and flux the joints appropriately, so that the pressure is available at the right spots. Now turn on the water heater to test for leaks.

If you find all of these too difficult or are too preoccupied with your work, you can always call upon the best professional plumbing contractor Plumber Toronto. They are always ready to help.

Everything You Need To Know About Flush Toilets

Plumber Toronto

More than 200 years ago when English inventor Alexander Cumming was patented with the design of flush toilet, little did he knew that this was going to be one of the greatest discoveries of all time. Though in 1596 Sir John Harington was the first one to describe the design of a modern toilet. The useful content of this blog is sponsored by Plumber Toronto

Working of Flush Toilets

The whole of the toilet can be divided into four parts. The handle, Tank, Lid and toilet bowl. While inside the tank is a float ball, float rod, siphon, inlet valve, inlet tube and a piston.

Now the inlet valve controls the flow of water through the inlet tube, as one presses the handle. When we push the handle, a liver inside the tank pulls the piston up, allowing some water inside the siphon, as the level of water drops the float ball gradually falls, the pressure on the inlet valve by the siphon rod is reduced, and thus water flows through the inlet valve, which refills the tank.

Now one often wonders why certain amount of water is left behind after we flush. This left out water is due to the shape of the flush toilet which is S, U, J or P shaped, this let out water acts as seal to the sewer gases.

Common problems and solutions

Slow flush - Even after repeated flushing, the flow of water is very slow. The probable reason behind it is deposit in the inside rim of the bowl, due to prolonged use and exposure to hard water. Partial blockage of toilet may also lead to this problem. Hook like substance could be used to clear it out, a hanger for instance. But one should not overdo it, as it may cause disfigurement or permanent damage.

Delay of flush during consecutive flushing - During every flush, as explained in the beginning the tank gets emptied, and the inbuilt mechanism helps it to restore the lost water through the inlet tube, but if the inlet tube is partially clogged ,requisite amount of water could not get in thus it requires lots of time to replenish the lost water. Finding the source of blockage and removing it will restore it to normal functioning.

Vibrations and sounds while flushing - Every time you flush your toilet, it seems that even the person out in the hall can be sure that finally you did your job. The source of these sounds could range from reasons like  ,as you flush a vacuum is  created which is equalized by rapid flow of water, but if the vent is blocked due to twigs and leaves or some other reason, you listen to these vibrating sounds, which is actually air passing to normalize the vacuum. Clearing the blockage will remove those uninvited sounds.

Leaking flush tank - With prolonged use, the seals start to corrode, these leads to leaking of water. Now these aerosols are capable of high infections as they are perfect source of very harmful disease causing bacteria and viruses. The source of the leak should be figured out and fixed with proper sealant.

Thus the problems we face with these flush toilets, does not mean one has to replace the whole thing, thus a hole in the pocket. A little bit of fixing, and a talk with your local plumber Toronto will do your job.

DIY Plumbing Tips for Your Bathroom

How many of you are facing difficult times due to several leaks in your bathroom? What most of us think of a bathroom leak is really disturbing. A bathroom leak repair is not a rocket science and it just needs a couple of hours (a day at most) to get executed.

In this article, I’ll be sharing some of the most useful tips from plumber Toronto to get your bathroom treated in a manner so that, you won’t have to suffer from the uncertainties of bathroom leaks.

Hot water is a proven agent for removing clogs from the drain pipes. It is the easiest and the smartest way to clear the jammed clogs from the pipelines. However, it is only useful for pipes of smaller circumference. A free flowing drainage system is an absolute necessity for a hygienic bathroom.

According to plumber Toronto, Most common causes of blockage are the hair fell from your head, shampoo sachets, soap chips and, plastic pouches. These unwanted blockages can be prevented by fitting special strainers. You can fit these special strainers in bath tubs and drainage nets to avoid blockages.

Another elementary thing which might require your attention is your shower heads. Have you noticed the uneven spray from your showerhead? This is caused by the dirt and minerals which get deposited in the pinholes of the showerhead which then block the water spray. Showerhead can be cleaned by unscrewing the nut known as “collar nut” and then cleaning the incoming and outgoing pin points. This is not a tricky thing as you can use any thin stick or even a metal wire for this purpose.

Another frequent plumbing problem happens is overflowing toilet tanks. This is the kind of problem which should ideally be treated by the experts because the toilet tanks have little minute mechanics to inlet and dispatch flush water. If you are not aware of the specifications of the mechanics, it is always better to call a professional plumber. However, if you know the basics, you can very well do it yourself.

You’ll have to look out for the level of water in the toilet flush tank and make sure that it is not getting overflown through the pipe. To make a conclusion, use water colors or any kind of colors from your kid’s stationary and put it into the flush tank. Now, come back after 10-20 minutes and check out the color of the deposited water. If the color is gone or faded, your water tank is leaking and it needs to get fixed.

Leaking bathroom taps are the most common plumbing problems which are caused by the old generation metal / plastic taps and / or, by low quality worn out pipe threads known as nipples. I would advise you to look out for a new Tap adapter (it has two ends : one plain and one female). If a leakage is not visible but nonetheless it is happening, Test plug should be used. A test plug is made of rubber which is used to seal the suspected pipe and then check the probable leakage area.

These were a handful tips which can be utilized in order to get a leakage free bathroom. There are more such tips which I’ll be covering in the coming articles.